Liquid glass for car

Liquid crystal display applies only to a qualitatively wash the body of the car. Carefully choose a quality car wash to get the perfect result. It is unacceptable for the use of napkins dirty or the low quality of the chemical products that damage the body paint of your vehicle and leave stains. Pay special attention to this!

Decide to use a protective coating, do not clean the wax and shampoo. It is better to use the following tools:

liquid crystal
  1. car cleaning shampoos are used to remove even more serious contamination due to the presence of the base number. Considered the most gentle means and wiper universal for all stains and traces of dirt.
  2. car shampoos are the best option before the application of liquid crystal. The composition effectively protects the car body from the risk of damage during washing. All the dirt, dust carefully and gently removed thanks to the unique components of the detergent.

Automotive cosmetics have included a sponge applicator for the application, gloves protection for hands, cotton towel and a microfiber cloth for the following phase of coating abrasive cleaning and polishing.

Cleaning car body

Not all stains and dirt are removed on the body, even after best quality wash. Traces of the birds, insects, buds of trees sometimes require additional purification step. Faces that means "Purification of the body of insects and bitumen".

The paint coating of the car, there is always pollution, which is imperceptible to the human eye. Here comes a cleansing clay, which eliminates deep stubborn stains and dirt from the small cracks, while some other media are absolutely powerless. It can also be used for the cleaning of glass and apply only on affected areas, not on the entire surface. The clay is used only to wet the car body.

You have to understand that ben has a car wash will allow as much time as possible to preserve the validity of the protection polishes "liquid crystal".

Abrasive polishing

The polishing abrasive is best done in special places, as there is a risk of damage to the paint. Working with pastes and polishing machine requires experience and skills in this business. First polishing is performed using a paste with a large particle abrasive. Completed the treatment, which removes the smallest scratches.

The drivers who decided to do it all by yourself, we recommend that you use the tool, which degreases the body and replace the polishing. It is thanks to this composition is achieved the maximum effect of the treatment of the painting the glass of the screen .

Application of liquid crystal

The whole process of application of wax, polymeric, and composite is reduced to a standard sequence of actions: application of funds, the waiting for the drying, work with a napkin. It would seem, nothing complicated, but it takes extra time and physical strength. The use is carried out without physical effort. The tool is easy to apply, without pressure, with special wipes included in the kit. The main advantage - there is no need to use the polishing machine.

Recommendations before using

  1. Do not use in high humidity.
  2. Do not use the product at a low temperature to avoid the condensation on the bodywork of the vehicle, which will have a negative impact on the protection of the functions of the polishes.
  3. The drying time of the composition of the most rapid in the summer.
  4. Limit the penetration of the composition in plastic and rubber parts in the car. Before the use of the composition of cover them with a protective film. The mixture is used only in the paint.
  5. The Polish is applied to the calm of the earth, as you can hit the solar ultraviolet radiation and dust.

The stages of application of glass protection

  1. The tool consists of two vials. Mix them with the other. Protective glass retains its properties within six hours of mixing. The remains can't be used.
  2. The mixture is applied in two phases and is distributed to the body, parallel movements.
  3. The car handling is carried out successively: roof, hood, trunk, right and left. Do not spray large areas, the use of small areas.
  4. The matte surface of the body – a characteristic feature of the partial drying. Take the cloth yellow and gently run the wipe. Not to be put in place for the presence of spots. The main thing is not overdry the composition, otherwise it will have to remove the paste abrasive and restart the processing of the bodywork of the vehicle.
  5. Cloth to do the polishing. Without much physical effort, you will receive a car from a dazzling Brightness.
  6. Carefully inspect the surface for any remaining missing or not sufficiently polished periods. It must be done immediately, as the protective glass loses its properties after six hours. If bad sections are found, proceed to the next part of the car for coating.

Now your car is protected from dirt, droplets of water only to drain out, leaving no traces and divorces. Japanese car cosmetics company is a reliable assistant to take care of your car.

You should also observe the following rules:

  1. To preserve the coating, do not use the vehicle at least two hours after application. The maximum exposure time will give the most effective result for the durability of the protection polishes.
  2. Liquid crystal can partially lose their properties in contact with water. It is not necessary to drive a car, after treatment, in the rain. It is recommended for a day to leave your car inside for the full completion of the application phase.
  3. Throughout the week, avoid chemical washes and wash with shampoo. Allowed to hit pieces of land on three days in water jets.
  4. In case you are not able to avoid exposure to rain for all ten days, apply silicone devices for the removal of droplets. The sun these drops acts as an optical lens, causing damage, such as coating and painting of the surface.

Adhere to the rules of application, you get the maximum protection for your car all year or in fifty touchless washes.

Steps to be followed after the application of

Liquid crystal display guarantees the car protection from negative environmental factors.

To maintain and increase the validity of the following tips will help you

  1. Avoid aggressive cleaning products: varnishes, glues and others.
  2. A large amount of dust and dirt negatively affect the protective properties of liquid crystal. You must control the cleaning of the car. At least once a month (at least) to use a polishing shampoo that is specially designed for the care of the body of a car, treat it with a protective Polish.

Step-by-step application instruction

Shine after idahot glass

The effective application of liquid crystal depends on the fulfillment of two conditions

  1. the coating process is carried out in different phases;
  2. mandatory observance of these time periods.

Be sure to know

You can't break the integrity of the packaging before use, the mixture loses its protective properties. Before the application of the bodywork of the vehicle should be carefully clean and dry, free of wax or grease residue. If there are stripes, and to work to remove them. Before you use a couple of times to shake the bottle. By using a sponge applicator to apply the gel to the surface of the car. To wait a specified period of time before the crime to the phase of polishing.

The vehicle is processed sequentially by parts:

  1. side (door);
  2. bell;
  3. ceiling;
  4. trunk;
  5. back.

Temporary recommendations in different moments of the year:

  1. in the spring, the autumn (between 10 and 20 º C in the shade, the polymerisation of the 10-minute, polished– 5 minutes);
  2. summer (20-35 ° C in the shade, the polymerisation of 5-minute, polished– 3 minutes);
  3. winter (from 10 ° C in the sun, the polymerization for 15 minutes, and polished– 10 minutes).

Do not use when temperatures are below zero!

Do not use in direct sunlight!

The resistance of the layer is broken from the direct light of the sun and ultraviolet light.

The liquid is not intended for long-term storage, designed for an exclusive use.

Avoid contact of cleaning throughout the week.

Do not use aggressive means to maintain the surface of the body of the car.

The lack of effect on the prolonged stage of drying (failure in time of polishing).