Relatively recently in the market appeared new from Japanese developers – the liquid crystal. Advanced motorists are able to evaluate the product and the experience of a "wow-effect" in my car. Today we are going to examine: what is the liquid glass for cars, what are the advantages and disadvantages of funds, how to apply liquid crystal and subsequently removed.
Liquid glass for cars are used as varnishes. In the treatment of the body or just auto creates a transparent film that protects the car's minor damage, adds Shine and novelty. Notice how the owners of cars, of colour after polishing becomes brighter. In addition to the effect of restore the colour and hide small defects, liquid glass repels water and the air.
Liquid crystal is of different types:
The last is the most rare, is used as a thermostat. Most often used for polishing kalium, because the varnishes on the basis of potassium that have better water-repellent properties.
The advantage of the use of liquid glass Polish over conventional lies in the comparative durability of water repellency, while retaining the original color and hide small defects. For comparison, the wax Polish is kept in the car to 1 car wash, polymer to 4-5, the abrasive is used in exceptional cases (as an example, to remove the glass). Of glass, will remain in the car for up to 30 washes.
Nanoceramics and liquid crystal – primary competitors in the market for automotive services. Nanoceramics is the material more expensive, but at the same time more durable. If liquid crystal in the domestic climate has a duration of 8 months (maximum one year), producers nanoceramics promise results of up to 3 years. In the choice between conventional Polish, ceramics and glass, to give preference to the last. Liquid crystal is a insurance of average between the expensive ceramic and conventional coatings. Whatever your decision, the choice is yours.
In spite of all the advantages of the procedure, there are some drawbacks. Among them:
So, You have weighed the pros and cons of liquid crystal for one car. Again be warned, coating machine liquid crystal is a difficult task procedure. In the case of a small mistake, the result can be disastrous. If you are sure that you have the sufficient knowledge for independent processing of the auto – forward!
The premises for processing must be clean. There are No currents of air, high humidity. The ideal temperature of 10-40 degrees. The fresh air processing machine, unfortunately, will not work. The cold of winter and the direct ultraviolet rays of the sun in the summer can have a negative impact on the result.
Before you start the treatment of auto liquid glass, you need to buy the following materials:
Tip: often in the shops of the liquid crystal is sold with some of these items. Best not to skimp and get a tool that includes the components necessary for the processing.
Before the application of the composition in the car, save your car from any dirt. If you have old Polish remove it. Then, dry and remove the fat from the car.
Before polishing, we recommend to read video how to apply liquid glass in the car. A clear process will be more clear, and some points at any time to re-read the instructions below.
Look for the purchased polishes the user manual in the Russian language. If there are, we suggest that you read them carefully before any action. Note also that the full polishing of the car is +/- 5 hours. Everything, because every detail of the body is processed separately and in various layers.
So, how to cover the auto with liquid crystal:
Repeat the procedure with each part of the machine. After all the manipulations, to leave the car for 5-6 hours to dry. After successfully polishing not wash the car in 1-2 weeks.
The rider questions, to wash the composition of the vehicle, in case of bad polishing. In the case that the procedure was a success and without defects, it is necessary to remove the liquid glass is not.
In the place of one of the manufacturers of liquid crystal to write that:
"Liquid crystal can be removed with any polishing with fine abrasives."
That is to say, to remove liquid glass from the bodywork of the vehicle, it is sufficient to Polish it with abrasives. How to write drivers, this method is not a panacea. The abrasive can't remove the part with the deep scratches. In addition, it carried out quickly and needs a lot of water in the process.
In case of successful processing machine with liquid crystal display, remove it from the vehicle will be successful only partially. So once again, think about whether the risk with the savings?